Shenzhen Hehejin Industrial Co., LTD.

PowMr EPever 10A 20A 12V/24V Auto Solar Charge Controller PowMr EPever 10A 20A 12V/24V Auto Solar Charge Controller

MPPT EPever Solar Charge Controller 40A 30A 20A 10A Tracer AN Series Back-light LCD Regulator for Lead-acid Lithium-ion Battery,can minimize the maximum power point loss rate and loss time,track the maximum power point of the PV array and obtain the maximum energy from solar modules under any conditions

  • Brand : PowMr
  • Product Name : Tracer 1206AN
Current Optional:
  • 10A
  • 20A
WHS Location:
Share this:

Description

The Tracer AN series. Based on common negative design and advanced MPPT control algorithm, with LCD displaying running status, this product is artistic, economical and practical. Improving the MPPT control algorithm further, Tracer AN series can minimize the maximum power point loss rate and loss time, quickly track the maximum power point of the PV array and obtain the maximum energy from solar modules under any conditions; and can increase the ratio of energy utilization in the solar system by 10%-30% compared with a PWM charging method. The limitation function of the charging power and current and reducingcharging power function automatic improve the stability which works even connecting oversize PV modules and in high temperature, and increase the professional protection chip for the communication port, further improving the reliability and meeting the different application requirements.

Feature:

Advanced MPPT technology, with efficiency no less than 99.5%\Ultra-fast tracking speed and guaranteed tracking efficiency

Advanced MPPT control algorithm to minimize the maximum power point loss rate and loss time

Wide MPP operating voltage range

High quality components, perfecting system performance, with maximum conversion efficiency of 98%

Accurate recognition and tracking of multiple-peaks maximum power point 

International famous brands of ST and IR's components of high quality and low failure rate are used, which can ensure the product’s service life

Charging power and current limitation function

Compatible with lead-acid and lithium-ion batteries

Battery temperature compensation function

Real-time energy statistics function

Overheating power reduction function

Multiple load work modes

The communication port adopts professional protection chip, which can provide 5VDC power supply, and has over-current and short-circuit protection. 

With RS-485 communication bus interface and Modbus communication protocol, it is available to meet various communication requirements in different situations.

Monitor and set the parameters via mobile phone APP or PC software 

Full-load operation without any drop in capacity within the range of working environment temperature 

Extensive electronic protection 

image.png

1. Connect components to the charge controller in the sequence as shown above and pay much attention to the “+” and “-”. Please don’t turn on the fuse during the installation. When disconnecting the system, the order will be reserved.

2. After installation, power the controller and check the LCD on. If it’s not on, please refer to chapter 4. Always connect the battery first, in order to allow the controller to recognize the system voltage.

3. The battery fuse should be installed as close to battery as possible. The suggested distance is within 150mm.

4. The Tracer-A series is a positive ground controller. Any positive connection of solar, load or battery can be earth grounded as required.

 Auto cycle interface

image.png

 Browse interface

image.png


Technology Parameter

Battery Voltage Parameters (parameters is in 12V system at 25, please use double value in 24V.)

Battery charging setting

Sealed

Gel

Flooded

User

Over Voltage Disconnect Voltage

16.0V

16.0V

16.0V

9~17V

Charging Limit Voltage

15.0V

15.0V

15.0V

9~17V

Over Voltage Reconnect Voltage

15.0V

15.0V

15.0V

9~17V

Equalize Charging Voltage

14.6V

——

14.8V

9~17V

Boost Charging Voltage

14.4V

14.2V

14.6V

9~17V

Float Charging Voltage

13.8V

13.8V

13.8V

9~17V

Boost Reconnect Charging Voltage

13.2V

13.2V

13.2V

9~17V

Low Voltage Reconnect Voltage

12.6V

12.6V

12.6V

9~17V

Under Voltage Warning Reconnect Voltage

12.2V

12.2V

12.2V

9~17V

Under Volt. Warning Volt.

12.0V

12.0V

12.0V

9~17V

Low Volt. Disconnect Volt.

11.1V

11.1V

11.1V

9~17V

Discharging Limit Voltage

10.6V

10.6V

10.6V

9~17V

Equalize Duration (min.)

120

——

120

0~180

Boost Duration (min.)

120

120

120

10~180

Electrical Parameters

 

ItemTracer 1206ANTracer 2206AN
System nominal
voltage
12V/24VDC Auto
Rated charge current10A20A
Rated discharge
current
10A20A
Battery voltage range

8~32V

Max. PV open circuit voltage46V
MPP voltage range(Battery voltage +2V)~36V
Max. PV input power130W/12V
260W/24V
260W/12V
520W/24V
Self-consumption<=12mA
Discharge circuit voltage drop<=0.23V
Temperature compensate coefficient-3mV/°C/2V (Default)
GroundingCommon negative
RS485 interface5VDC/100mA
LCD backlight time60S (Default)
Environmental Parameters
Working environment temperature-25°C~+50°C(100% input and output)
Storage temperature range-20°C~+70°C
Relative humidity<=95%, N.C.
EnclosureIP30
Dimension172x139 x 44mm220x154x 52mm
Mounting dimension130x130mm170x145mm
Terminal12AWG(4mm 2 )6AWG(16mm 2 )
Recommended cable12AWG(4mm 2 )10AWG(6mm 2 )

 

 


Video Center


×

Contact Us

captcha