Shenzhen Hehejin Industrial Co., LTD.

Powmr EPever 100A/80A/60A/50A MPPT 200V Solar Charge Controller Powmr EPever 100A/80A/60A/50A MPPT 200V Solar Charge Controller

Powmr EPever PV 200V 100A/80A/60A/50A solar charge controller LCD display lithium battery for solar RV, household system Solar Panel Input Regulator.The controller utilizes standard Modbus communication protocol, making it easy for users to check and modify system parameters on their own. Besides, by providing free monitoring software, we give users the maximum convenience to satisfy their varied needs for remote monitoring.

  • Brand : PowMr
  • Product Name : 10420AN
Current Optional:
  • 100A
  • 80A
  • 60A
  • 50A
WHS Location:
Share this:

Product Description

Features:

 CE certification(LVD EN/IEC62109,EMC EN61000-6-1/3)

 High quality & low failure rate components of ST and Infineon to ensure the product’s life

 Advanced MPPT technology & ultra-fast tracking speed, with tracking efficiency no less than 99.5%

 Maximum DC/DC transfer efficiency is as high as 98.6%★, full load efficiency is up to 98%★

 Advanced MPPT control algorithm will minimize the MPP loss rate and loss time

 The accuracy of the recognition and tracking at the highest point of multiple-peaks MPPT

 The wider range of MPP operating voltage.

 Auto control system to limit the charging power & current go over the rated value.

 Support 4 charging options: Sealed, Gel, Flooded and User.

 Support the lead-acid and lithium batteries

 Real-time energy recording and statistical function

 Automatic over-temperature power reduction function

 Hundred percent full load operation in working environment temperature range within charging & discharging

 Support up to 6 units in parallel to expand system

 Load relay control external load switch signal to realize diversified load work modes

 The first and the second disconnection of load control, contain two relay’s contact.

 Auto-control of utility and generator relay design

 Utility or generator auto-control relays make it easy to compose the hybrid power system

 The remote temperature and the voltage sensor design will collect accurate data of battery temperature and voltage

 Isolated RS485 with 5VDC/200mA to protect output for no power devices with MODBUS protocol

 To monitor or set the parameters by using the phone Apps or PC software.


General Installation Notes

 -Before installation, please read through the entire installation instructions to get familiar with the installation steps.

 -Be very careful when installing the batteries, especially flooded lead-acid battery. Please wear eye protection, and have fresh water available to wash and clean if any contact with battery acid.

 -Keep the battery away from any metal objects, which may cause short circuit of the battery.

 -Explosive battery gases may come out from the battery during charging, so make sure ventilation condition is good.

 -Lead-acid battery are recommended, other kinds please refer to the battery manufacturer.

 -Ventilation is highly recommended if mounted in an enclosure. Never install the controller in a sealed enclosure with      flooded batteries! Battery fumes from vented batteries will corrode and destroy the controller circuits.

 -Loose power connections and corroded wires may result in high heat that can melt wire insulation, burning surrounding materials, or even causing fire. Ensure tight connections and use cable clamps to secure cables and prevent them from swaying in mobile applications.

 -Battery connection may be wired to one battery or a bank of batteries. The following instructions refer to a singular battery, but it is implied that the battery connection can be made to either one battery or a group of batteries in a battery bank.

 -Multiple same models of controllers can be installed in parallel on the same battery bank to achieve higher charging current. Each controller must have its own solar module(s).

 -Select the system cables according to 5A/mm 2 or less current density in accordance with Article 690 of the National Electrical Code, NFPA 70.


photo 14.jpg

photo 15.jpg

photo 17.jpgMPPT 4.jpg




Technology Parameter

Item

Tracer5420AN

Tracer6415AN

Tracer8420AN

Tracer10420AN

Nominal System Voltage

12/24/36/48VDC Auto

Battery Input Voltage Range

8V~68V

Battery Type

Sealed(Default)/Gel/Flooded/User

Battery fuse

80A/58V

150A/58V

Rated charge current

625W/12V

1250W/24V 1875W/36V 2500W/48V

1000W/12V 2000W/24V 3000W/36V 4000W/48V

1000W/12V 2000W/24V 3000W/36V 4000W/48V

1250W/12V 2500W/24V 3750W/36V 5000W/48V

Max. PV open circuit voltage

200V

MPP Voltage Range

(Battery Voltage +2V)~108V

Tracking efficiency

≥99.5%

Max. conversion efficiency

98.3%

Full load efficiency

97.8%

98.0%

Temperature compensate coefficient

-3mV/°C/2V(Default)

Self-consumption

98mA/12V;60mA/24V;50mA/36V;46mA/48V

Grounding

Common negative grounding

Relay

Rated Value:5A/30VDC; Max. Value:0.5A/60VDC

RS485 interface

RS485(RJ45)

LCD backlight time

Default:60S,Range:0~999S(0S:the backlight is ON all the time)

Ambient temperature range

-25°C~+60°C(Derate above 45°C)

LCD temperature range

-20°C~+70°C

Storage temperature range

-30°C~+85°C

Relative humidity range

5% to 95% (N.C.)

Enclosure

IP20

Pollution degree

PD2

Dimension

261×216×119mm

Mounting dimension

180×204mm

Mounting hole size

Φ7

Terminal

6AWG/16mm 2

Recommended cable Safety

6AWG/16mm 2

EMC

EN61000-6-3/EN61000-6-1

FCC

47 CFR Part 15, Subpart B

ROHS

IEC62321-3-1

 




Video Center


×

Contact Us

captcha