Shenzhen Hehejin Industrial Co., LTD.

PowMr 12V/24V 60A 80A 30A PWM Solar Charge Controller With LCD Display PowMr 12V/24V 60A 80A 30A PWM Solar Charge Controller With LCD Display

I series controller is a kind of intelligent,multi-purpose solar charge and discharge controller. The family use the fixed LCD display, with a very friendly interface; various control parameters can be flexibly set, fully meet you’re your various application requirements. I series controller has following features:1.Image of LCD graphic symbol 2.Simple button operation 3.Automatic Identification System Voltage level 4.Intelligent PWM charge mode 5.Automatic Temperature Compensation 6.Adjustable charge-discharge control parameters 7.Settable Operating mode of Load 8.Overload, Short Circuit Protection 9.Remote monitoring and control function (custom) 10.Battery reverse-discharge protection 11.Battery Low Voltage Disconnection (LVD) 12.Battery reverse connection protection 13.Accumulated function of charge and discharge Ampere hours

  • Brand : PowMr
  • Product Name : 60I
Current:
  • 60A, 80A
Model:
  • 60I, 80I
WHS Location:
Share this:

Description

PowMr 12V/24V 60A 80A 30A PWM Solar Charge Controller With LCD Display


Feature

  • Brand:PowMr

  • Product Model: 60I

  • Image of LCD graphic symbol         

  • Simple button operation

  • Automatic Identification System Voltage level    

  • Intelligent PWM charge mode

  • Automatic Temperature Compensation

  • Adjustable charge-discharge control parameters

  • Settable Operating mode of Load               

  • Overload, Short Circuit Protection

  • Remote monitoring and control function (custom)  

  • Battery reverse-discharge protection

  • Battery Low Voltage Disconnection (LVD)

  • Battery reverse connection protection

  • Accumulated function of charge and discharge Ampere hours

Overview

Read all of the instructions and cautions in the manual before beginning the installation.

1.Brand: PowMr

2.Product Model: 60I

3.I series controller is a kind of intelligent,multi-purpose solar charge and discharge controller.

4.The family use the fixed LCD display, with a very friendly interface; various control parameters can be flexibly set, fully meet you’re your various application requirements. 



60I-12.jpg

60I.main.jpgInstallation

Install

① Ready tools and cables. Encourage you to matching the right cables. Ensure that the current density<4mm2 Controller that is conductive to reducing the line voltage drop.

Recommended: 60A with 20mm2 cable.

Check weather the installation sites compliance with the relevant safety requirements. Please avoid the damp, dusty, there is a place flammable, explosive and corrosive gases use the controller to install.     

② Install the controller into a fixed vertical plane. See section 5 of the  pore size and pore spacing. In order to ensure a good thermal control conditions, please set aside each 10cm below the controller space.

③ As shown on the right, connect the (1) Load, (2) Battery and (3) Solar Panel to the controller according to the order of (1) (2) (3). Pay attention to the load, battery, solar panel and controller of same polarity.

④ Put into the external temperature sensor on the left of the controller (probe port). The temperature sensor should be similar space with battery. (Otherwise, the controller will control the parameters of all wrong temperature compensation.)

⑤ If you have remote monitoring and control function, please insert one end of the included

   communication wire on the right of the controller (communication port), the other end to connect to

   The host computer.

Demolition: To prevent accidents, please order the demolition of solar panels, battery and load disconnect with controller.

NoteBattery polarity will not damage the controller, but you will have a load equipment security risks.

Technology Parameter

Model

60I

80I

Rated current

60A

80A

Rated voltage

12V/24V

Maximum voltage

 of solar panel

≤50V

Float voltage

13.7/27.4V

Low Voltage Disconnection

10.7/21.4V

Low Voltage Reconnection

12.6V/25.2V

No-load loss

<30mA

Loop Voltage Drop

≤200mV

Charging mode

PWM

Temperature compensation

-4mV/Cell/℃

Installation Cable No.

>3# AWG (<25mm2)

 Operating temperature

-20℃~50℃

Storage temperature

-30℃~70℃

Humidity requirement

≤90%,without condensation

Size/Weight

130mm×188mm×62mm/700g

Spacing of mounting holes

98 mm×178 mm --Φ5


×

Contact Us

captcha